如何修理旧叉车的转向节?
发布时间:2021-11-10 点击:546
转向节的主要功能部分山东叉车驾驶叉车时在水平道路,叉车的轮上下波动与水平轴为中心,它可以减少框架的扭力,确保每个叉车轮的负载是偶数,并确保叉车运行稳定。山东叉车转向节问题如何处理?
the main function of the steering knuckle is that when shandong forklift drives a forklift on the horizontal road, the wheels of the forklift fluctuate with the horizontal axis as the center. it can reduce the torque of the frame, ensure that the load of each forklift wheel is even, and ensure the stable operation of the forklift. how to deal with the steering knuckle problem of shandong forklift?
如何修理旧叉车的转向节?
how to repair the knuckle of old forklift?
1、二手叉车转向节颈部出现裂纹时,应及时更换。
1. in case of cracks on the steering knuckle neck of second-hand forklift, it shall be replaced in time.
2. 使用过的叉车转向节配件e、f轴承的磨损一般不应超过0.05mm。如果大于这个值,可以镀铬修复。
2. the wear of bearings e and f of used forklift steering knuckle fittings shall not exceed 0.05mm generally. if it is greater than this value, it can be repaired by chrome plating.
三、转向节推力轴承平面,应平整,如不平整应修理。
iii. the plane of the thrust bearing of the steering knuckle shall be flat, and if not, it shall be repaired.
4. 二手叉车转向节配件的螺纹损坏超过2颗牙时,可以修复螺母,也可以堆焊后重新旋回螺纹。
4. when the threads of the steering knuckle parts of the second-hand forklift are damaged by more than 2 teeth, the nuts can be repaired, or the threads can be screwed back after surfacing.
五、二手叉车转向节的装配与调整。指节与指节销轴之间的间隙不得大于0.1mm。
v. assembly and adjustment of used forklift steering knuckle. the clearance between knuckle and knuckle pin shaft shall not be greater than 0.1mm.
6. 转向节与转向桥的端部间隙一般为0.05-0.1mm。如果端部间隙过大,可加入调整垫圈。
6. the end clearance between the knuckle and the steering axle is generally 0.05-0.1mm. if the end clearance is too large, the adjusting washer can be added.
7. 二手叉车转向节轴与转向桥之间滚针轴承的最大间隙不得大于0.1mm。
7. the maximum clearance of needle bearing between knuckle shaft and steering axle of second-hand forklift shall not be greater than 0.1mm.
8. 转向节销孔误差为0.06mm。当销孔大于0.1mm时,可用主销轴将销孔扩至修复尺寸。
8. the error of knuckle pin hole is 0.06mm. when the pin hole is larger than 0.1mm, the main pin shaft can be used to expand the pin hole to the repair size.
当使用叉车转向板销孔磨损时,应不大于0.15mm,否则可按合页修复大小,用主销轴。
when using forklift steering plate pin hole wear, should not be more than 0.15mm, otherwise can repair size according to hinge, use main pin shaft.